How to Edge Band Curved Surfaces with Images223

Edge banding is a technique used to cover the exposed edges of plywood, MDF, or other wood-based panels with a thin strip of material, typically PVC or ABS plastic. This not only enhances the aesthetics of the finished product but also protects the edges from moisture, wear, and chipping. While edge banding is relatively straightforward on straight edges, it can be more challenging when dealing with curved surfaces.

In this guide, we will provide step-by-step instructions on how to edge band curved surfaces using a variety of methods. We will also include images to help illustrate the process.

Method 1: Using a Handheld Router

One of the most common methods for edge banding curved surfaces is to use a handheld router. This method requires a bit of practice to master, but it can produce excellent results.

To edge band a curved surface using a handheld router, you will need the following supplies:* A handheld router
* A flush trim bit
* A guide bearing
* Edge banding material
* Wood glue

Step 1: Prepare the edge banding material

Cut the edge banding material to the desired length. Apply a thin layer of wood glue to the back of the edge banding material.

Step 2: Attach the guide bearing to the router

Attach the guide bearing to the router base. The guide bearing should be the same diameter as the flush trim bit.

Step 3: Set the router depth

Set the router depth so that the flush trim bit just barely touches the surface of the wood. You may need to adjust the depth as you work.

Step 4: Route the edge banding material

Hold the router firmly against the edge of the wood and slowly route the edge banding material into place. Be sure to keep the guide bearing flush against the surface of the wood.

Step 5: Trim the excess edge banding material

Once the edge banding material has been routed into place, use a sharp knife or utility knife to trim any excess material. Be careful not to cut into the wood.

Method 2: Using a Vacuum Press

Another method for edge banding curved surfaces is to use a vacuum press. This method is less labor-intensive than using a handheld router, but it requires specialized equipment.

To edge band a curved surface using a vacuum press, you will need the following supplies:* A vacuum press
* Edge banding material
* Wood glue

Step 1: Prepare the edge banding material

Cut the edge banding material to the desired length. Apply a thin layer of wood glue to the back of the edge banding material.

Step 2: Place the edge banding material on the curved surface

Place the edge banding material on the curved surface, aligning it with the edge of the wood. Be sure to press the edge banding material firmly into place.

Step 3: Apply vacuum pressure

Close the vacuum press and apply vacuum pressure. The vacuum pressure will hold the edge banding material in place while the glue dries.

Step 4: Remove the edge banding material

Once the glue has dried, open the vacuum press and remove the edge banding material.

Method 3: Using Contact Cement

A third method for edge banding curved surfaces is to use contact cement. This method is quick and easy, but it is important to use caution when working with contact cement, as it is highly flammable.

To edge band a curved surface using contact cement, you will need the following supplies:* Contact cement
* Edge banding material
* A brush or roller
* A clean cloth

Step 1: Prepare the edge banding material

Cut the edge banding material to the desired length.

Step 2: Apply contact cement to the edge banding material

Apply a thin layer of contact cement to the back of the edge banding material. Be sure to follow the manufacturer's instructions for applying contact cement.

Step 3: Apply contact cement to the curved surface

Apply a thin layer of contact cement to the curved surface, aligning it with the edge of the wood. Be sure to follow the manufacturer's instructions for applying contact cement.

Step 4: Press the edge banding material into place

Press the edge banding material into place, aligning it with the edge of the wood. Be sure to press the edge banding material firmly into place.

Step 5: Remove any excess contact cement

Use a clean cloth to remove any excess contact cement from the surface of the wood.

2024-12-19

Previous：How to Manually Apply Wood Edge Banding

Next：How to Edge Band Curved Surfaces: A Step-by-Step Video Guide